Recycle TI Comparators:High-Speed/Low-power/High-Voltage/Automotive Comparator
TI’s automotive-grade comparator series is designed for applications such as vehicle power management, motor control, BMS battery monitoring, ADAS signal detection, body protection and in-vehicle lidar. All products meet AEC-Q100 automotive certification standards and cover multiple product lines ranging from ultra-low-power, medium-speed precision, nanosecond-level high-speed, and 40V high-voltage product lines, balancing speed, power consumption, voltage withstand capability and automotive reliability. They serve as core analogue components for in-vehicle overvoltage and undervoltage protection, current threshold detection, pulse edge recognition and fault latching.
I. Core Automotive-Grade Specifications
The entire range of models with the ‘Q1’ suffix is AEC-Q100 certified, predominantly at Grade 1. The operating temperature range is –40°C to +125°C, with some models supporting a Grade 0 high-temperature version; a built-in power-on reset (POR) feature allows control of the output state upon power-up, preventing false triggering during system start-up; HBM and CDM electrostatic discharge (ESD) protection meets automotive-grade ESD requirements; the devices support both push-pull and open-drain output architectures, making them suitable for 5V logic, high-side drive, multi-device line and fault aggregation designs; numerous models incorporate fixed or configurable hysteresis, reducing output jitter caused by input noise and simplifying peripheral circuitry.
II. Analysis of Four Major Product Categories
1. High-Voltage Automotive-Grade Comparators (TLV1805-Q1 / TLV183x-Q1 / TLV184x-Q1)
This is TI’s flagship family of comparators for the automotive high-voltage domain. They support a wide supply voltage range of 2.7V to 40V, making them suitable for 12V and 24V vehicle batteries and high-voltage bus sampling applications. With rail-to-rail inputs, they can sample close to the positive and negative supply rails without the need for additional voltage-boosting circuits.
The TLV1841-Q1 has a propagation delay of 65 ns, making it a high-speed variant within the high-voltage range, suitable for rapid overcurrent and overvoltage protection; the TLV181x-Q1 has a delay of 420 ns and lower quiescent current, focusing on long-term monitoring applications; the TLV1805-Q1 features a shutdown pin, with a sleep mode that further reduces quiescent power consumption, making it suitable for battery management system (BMS) monitoring nodes that remain constantly active. The open-drain versions can be connected directly to high-voltage fault buses, whilst the push-pull versions are suitable for direct drive of MCU I/O. Typical applications include: BMS cell voltage monitoring, in-vehicle DC-DC overvoltage protection, current-limiting detection for relay drivers, and fault diagnosis for chassis actuators.
2. High-Speed Automotive-Grade Comparators (TLV321x-Q1 / TLV3603-Q1)
The TLV321x-Q1 is a cost-effective, high-speed automotive-grade comparator, available in single, dual or quad-channel configurations, with a static current of just 40 μA per channel, a stable propagation delay of 40 ns, built-in 1.8 mV hysteresis, excellent offset voltage control, a supply voltage range of 1.8 V to 5 V, and rail-to-rail inputs. It balances high-speed response with power consumption, making it suitable for low-cost, high-speed threshold detection.
The TLV3603-Q1 belongs to the ultra-high-speed category, with a propagation delay as low as 2.5 ns and high bandwidth. It is suitable for LiDAR pulse discrimination, high-speed clock recovery and high-speed differential signal detection. It features a single-channel push-pull output, operates on a supply voltage of 2.4 V to 5.5 V, and incorporates built-in latch, adjustable hysteresis and POR functions, making it ideal for signal conditioning in ADAS perception front-ends. The key advantage of these high-speed models is their strong edge-capture capability, enabling them to recognise narrow pulse signals and overcoming the slow response associated with standard operational amplifiers in comparator mode.
3. Ultra-low-power automotive-grade comparators (TLV370x-Q1, TLV703x-Q1, TLV704x-Q1)
The TLV370x-Q1 is TI’s benchmark for ultra-low power consumption, with a single-channel quiescent current of less than 560 nA, placing it in the nA range. It operates on a supply voltage of 2.7 V to 16 V and features a push-pull output. it is automotive Grade 1 certified and suitable for in-vehicle nodes that remain constantly powered, are battery-powered, and are extremely sensitive to quiescent current—such as smart keys, remote T-BOX wake-up detection, and battery leakage monitoring in sleep mode.
The TLV703x-Q1 and TLV704x-Q1 are also ultra-low-power rail-to-rail input comparators that balance response speed with ultra-low power consumption, achieving fast transition times whilst operating at the nA level. Their compact packaging makes them suitable for in-vehicle infotainment systems, sensor sub-boards and small body control units where PCB space is limited. The core value of the low-power series is to reduce static power consumption and prevent battery drain when the vehicle is switched off and left stationary.
4. Classic General-Purpose Automotive-Grade Comparators (LM2903L-Q1, LM2901V-Q1, LM339LV-Q1)
The LM2903L-Q1 is a dual-channel comparator and the LM2901V-Q1 is a four-channel comparator; both support a maximum supply voltage of 32 V, feature open-drain outputs and built-in latch functionality, with a delay of approximately 1 μs. Offering significant cost advantages and a mature ecosystem, they are the standard choice for traditional body control, fan control and simple protection circuits; The LM339LV-Q1 is a low-voltage variant, optimised for low-voltage operation and suitable for 3.3V-domain automotive boards. Whilst these devices do not offer high speed, their stability has been thoroughly validated in automotive applications and their supply chain is well-established, making them suitable for non-high-speed protection scenarios.
![]()
III. Logic for Comparing Key Parameters During Selection
- Priority for high-voltage buses, BMS and 24V systems: Select the TLV18 series Q1, with a 40V rating, available in both high-speed (TLV184x-Q1) and low-power (TLV181x-Q1) versions
- For nanosecond-level high-speed pulse detection, radar and high-speed signals: TLV3603-Q1; for applications requiring high speed whilst minimising cost and power consumption: TLV321x-Q1
- For sleep/standby modes, low leakage current and continuous battery power supply: TLV370x-Q1 and TLV704x-Q1, with nA-level quiescent current
- High-volume, general-purpose protection with a focus on cost: LM2903L-Q1, LM2901V-Q1
IV. Typical Automotive Application Scenarios
1. Battery Management System (BMS): Cell overvoltage, undervoltage, equalisation current comparison, and rapid short-circuit protection; prioritise the TLV184x-Q1 high-voltage, high-speed variant
2. ADAS and Sensing Units: Lidar echo pulse detection, optical signal threshold discrimination; use the TLV3603-Q1 ultra-high-speed comparator
3. Body and T-BOX: Wake-up signal detection, battery idle monitoring; use the TLV370x-Q1 ultra-low-power models
4. In-vehicle power boards: Overvoltage and undervoltage protection for DC-DC and LDO outputs, current-limiting detection; the TLV321x-Q1 strikes a balance between speed and power consumption
5. Motor, pump and fan controllers: Overcurrent fault detection and stalled-rotor detection; both the LM2903L-Q1 and TLV18 series are suitable
V. Details of the Electronic Component Recycling Services Offered by Shenzhen Mingjiada Electronics Co., Ltd.
Shenzhen Mingjiada Electronics has long been serving factories, distributors, traders and solution providers, specialising in the recycling of all types of original, unused electronic stock, project offcuts, cancelled order materials, goods returned from bonded warehouses, and electronic materials from customs confiscation auctions. As a one-stop service provider for realising the value of component inventory—integrating valuation, inspection, handover and settlement—we operate in parallel with our spot component supply business, focusing on revitalising idle semiconductor assets to alleviate the financial pressure caused by inventory build-up, expiring materials and warehousing losses.
1. Sources of Materials for Recycling
We accept idle electronic materials from a variety of scenarios, including factory surplus arising from cancelled production orders, product iterations and upgrades, and project wind-downs; excess stock held by agents and distributors; goods returned from bonded warehouses; compliant electronic components from customs auctions and confiscated goods; clearance stock from company wind-ups; and surplus samples and small-batch materials from R&D over-procurement. We can assess both full trays of bulk stock and scattered small quantities of sample materials, with no restrictions on batch size.
2. Scope of Materials Accepted
Integrated circuits, 5G chips, new energy ICs, IoT ICs, Bluetooth ICs, V2X ICs, automotive-grade ICs, communications ICs, artificial intelligence ICs, etc. In addition, we supply memory ICs, sensor ICs, microcontroller ICs, transceiver ICs, Ethernet ICs, Wi-Fi chips, wireless communication modules, connectors and other electronic components.
3. Rules for Grading and Valuation of Components
We employ a transparent three-tier grading system (A/B/C). Quotations are determined based on a comprehensive assessment of model scarcity, market conditions, production cycle, packaging condition, batch number and original manufacturer’s warranty information. There are no hidden deductions:
Grade A: Original manufacturer’s vacuum desiccant pouch intact, original tray unopened, packaging labels complete, in pristine condition; purchased at a premium price in line with market rates;
Grade B: Minor damage to outer packaging; desiccant bag opened; slight oxidation of pins; fully functional; assessed at a discounted rate;
Grade C: Cosmetic defects; severely damaged packaging; suitable for dismantling, refurbishment or sorting; purchased at residual value.
4. Standardised Recycling Transaction Process
1. Submission of Documentation for Initial Assessment: The client compiles a bill of materials, specifying model, brand, batch, quantity, packaging type and condition, whilst simultaneously sending actual photographs of the materials and circuit board labels to the assessment team;
2. Rapid Quotation: The assessment team generally completes the initial assessment within 24 hours and issues a formal quotation; verification periods may be extended for bulk stock or specialised automotive/aerospace components;
3. Physical Verification and Confirmation: We support on-site inspections at the client’s premises or the client sending samples for testing; door-to-door collection can be arranged in multiple locations across mainland China, whilst cross-border materials returned to the port can be handled via our Hong Kong warehouse for delivery; non-disclosure agreements can be signed as required to protect client project and supply chain information from disclosure;
4. Contract Signing, Delivery and Settlement: Both parties confirm the price and sign a formal purchase and sale contract; upon successful acceptance of the materials, settlement is made in cash. We support corporate bank transfers, maintain sufficient funds, do not act as agents, and do not withhold payments, thereby helping businesses rapidly recover cash flow.
5. Core Business Advantages
1. Market Expertise: We specialise in the semiconductor spot market and possess in-depth knowledge of material values across sectors including industrial, automotive, telecommunications, AI servers, humanoid robots and satellites; we can also assess niche, scarce and discontinued materials;
2. Transaction Confidentiality: We strictly enforce client information confidentiality protocols; project documentation and client inventory details remain confidential, making our services suitable for solution providers, defence industry suppliers and automotive supply chain clients;
3. Flexible Services: We accept both large and small batches, catering to both factory-wide stock clearance and scattered R&D samples; we offer door-to-door collection within China, as well as customs clearance and delivery solutions for cross-border returns;
4. Compliant Disposal: Recovered materials undergo sorting and testing; qualified, original-packaged components enter the spot market, whilst non-conforming materials are dismantled and processed in accordance with regulations, thereby promoting the circular economy for electronics and mitigating the risks associated with non-compliant waste disposal;
5. Independent Business Structure: The recycling and spot supply operations are managed separately; whilst we recover idle market stock, we simultaneously supply original components to external clients, thereby establishing a closed-loop supply chain capability.
Kontak Person: Mr. Sales Manager
Tel: 86-13410018555
Faks: 86-0755-83957753